Ten tons of intermediate frequency furnace tubes hose with much

by:Hengyang Furnace     2020-10-26
Ten tons of intermediate frequency furnace tubes hose with how technology encyclopedia 20 tons of intermediate frequency furnace, how much refining furnace a: basic not achieve the dephosphorization in medium frequency furnace, liquid steel dephosphorization is only slagging, namely to produce phosphate, actual production by the lime to slagging, so if not possible, a lot of steel with electric arc furnace and ladle refining furnace to adjust the composition of phosphorus of the liquid steel. 40 tons of intermediate frequency furnace need how much dust catcher ten tons of intermediate frequency furnace tubes hose with a: you said the question is too specific, intermediate frequency furnace choose how much dust catcher, need according to the actual situation of intermediate frequency furnace to you selection such as: intermediate frequency furnace flue gas outlet temperature is how many? Exit diameter have how old? How much air volume requirements? Are there any requirements on material? And so on, need to know the above technical parameters can be for you to choose the rules of the corresponding filter. The calculation method of 20 tons of intermediate frequency furnace and alloy ten tons of intermediate frequency furnace tubes hose how answer: the calculation of the steel water check for the amount of alloy and carbon steel, low alloy steel alloy addition amount of calculation of A steel water check in practical production, due to measurement, furnace charge quality fluctuation or operating factors ( Such as oxygen iron loss, big run boiling steel and iron ore, etc. ) , there will be a weight does not conform to the actual weight of the liquid steel and plan, to control and chemical composition of casting foundry. 30 t intermediate frequency furnace to how much capacity of the transformer is appropriate thanks a: transformer capacity should be 24000 kva, but should use rectifier transformer change this. If it is 12 send wave stove should be 12000 * 2 kva. But you said 30 t refers to holding furnace, medium frequency furnace melting furnace. I said is melting furnace transformer power. High-power circulating pump more than 15 tons of intermediate frequency furnace match ten tons of intermediate frequency furnace tubes hose how answer: ha ha, you can go to induction equipment net, an intermediate frequency furnace, intermediate frequency electric furnace equipment industry website. The most authoritative, oh. The first is the baidu: induction equipment network. 05 how much tons of intermediate frequency furnace transformer answer: 5 tons of intermediate frequency electric furnace is 250 kw, short-term application 315 kva transformer of up to 300 kw. Please take the answer and support me. 3 tons of intermediate frequency electric furnace need how much ten tons of intermediate frequency furnace transformer brass hose with a: 3 tons of intermediate frequency electric stove will need the following working voltage 500 v, heat insulation class is F of special transformer. With special purpose transformer known as special transformer. Transformer except for ac voltage conversion, and various other USES, such as the change of power frequency, rectifier equipment of the power, the power of the electric welding equipment, electric power and voltage transformer, electric. 25 tons of intermediate frequency furnace transformer much answer: 25 tons of intermediate frequency furnace need 12000 kw transformer, the input voltage of 100000 v, output voltage 1250 v. What is the copper pipe role of intermediate frequency furnace answer: produce eddy current heating effect, cooling effect of the water in the copper pipe at the same time. What material of intermediate frequency furnace lining a: lining made of brick masonry, because each part lined with different working conditions, use of refractory material and performance is also different. Such as the upper lining main consideration in shaft wear-resisting, furnace body and the furnace waist mainly considering thermal shock damage and alkali erosion, bosh main consideration at the beginning of high FeO slag erosion, hearth, main consideration molten iron mechanical erosion resistance of furnace bottom and refractory. Ten tons of intermediate frequency furnace tubes hose with much technical data of 20 tons of intermediate frequency furnace is how many meters high ten tons of intermediate frequency induction coil, furnace tubes hose how answer: this has no fixed value, according to your industry, the production of raw materials, production process, the power supply ability, etc. , after a careful calculation. 20 tons of intermediate frequency furnace into the line voltage ten thousand v to ten tons of intermediate frequency furnace transformer much brass hose with how much a: 20 tons of intermediate frequency furnace, about 10000 kw power rating, need to choose 12000 kva transformer, if there are no other load cases. About the power of intermediate frequency furnace present 08 calculation is ok. 5 tons of electric furnace transformer should be as large copper tube hose with 10 tons of intermediate frequency furnace answer: five tons of electric arc furnace transformer of 3200 kva, change especially, generally for the oil and water cooling, 10 kv or 35 kv, generally for 10 kv, long-term overloaded by 20%. 25 tons of intermediate frequency furnace current-limiting how appropriate ten tons of intermediate frequency furnace tubes hose with how much a: hehe want to see more power on the stove. Country is how intermediate frequency electric furnace for iron and steel industry to allow 10 tons of intermediate frequency furnace tubes hose how answer: all of the intermediate frequency furnace smelting iron and steel process is not allowed, has nothing to do with the tonnage of the furnace. Because of intermediate frequency furnace can not adjust the composition of molten steel, just melting scrap steel, smelting by 'steel' there is no way to determine brand, mechanical performance is impossible. 5 tons of intermediate frequency furnace cooling water system ten tons of intermediate frequency furnace tubes hose with how much a: cooling water system parameters, feed water pressure or less 5-03 mpa water temperature 35 ℃ cooling water outlet temperature of 55 ℃ or less consumption of 50 t/h water cooling system of water-cooling system points inside and outside two internal circulation loop system including type radiator stainless steel water tank stainless steel stainless steel stainless steel pipeline pump valve is mainly used for power supply cooling condenser copper platoon, the system set on the tank. Medium frequency furnace melting cast iron tonnage costs ten tons of intermediate frequency furnace copper tube hose with how much a: this depends on many factors, such as the choice of electric furnace, the selection of the transformer, the selection of raw materials, all you have to do the kinds of castings, electricity, etc. , you need to provide data to calculate the cost.
electric metal melting furnace is an inevitable and critical part of being a manufacturer, and it's more complicated than just manufacturing products and serving customers.
Many websites provide additional information on the topic of cast iron melting furnace. One such site worth visiting is Induction furnace, Induction melting furnace manufacturer, induction furnace manufacturers.
An interesting website that contains directions (and recommends items) for metal melting furnace steel continuous casting machine is Induction furnace, Induction melting furnace manufacturer, induction furnace manufacturers. Find us on Induction furnace, Induction melting furnace manufacturer, induction furnace manufacturers, your problem will be fixed.
We believe in keeping the customers happy and providing them with induction heating machine at a very competent price.
Custom message
Chat Online 编辑模式下无法使用
Chat Online inputting...