Intermediate frequency furnace circulating water charged technology an intermediate frequency furnace circulating water temperature range, is one of the high temperature how many answer: there is no uniform standard, some local environment is poor, the water temperature with five, sixty degrees.
Low temperature can control some, of course, will be better.
Medium frequency furnace has dc voltage no intermediate frequency voltage is what reason?
Answer: the failure analysis and treatment: the failure phenomenon does not belong to the intermediate frequency power supply failure, but because of the load impedance is too low to cause, should readjust to load impedance.
In the circuit of pressure load, due to the damage to dismantle series compensation capacitor, not replace, or blindly pursue high power and increase compensation capacitor unchecked, load compensation amount.
Intermediate frequency furnace need power consumption per ton hot metal how many degrees?
Intermediate frequency furnace circulating water charged a: our company one and 12 t, 30 t last month, the average power consumption is 667 kw per ton, large-tonnage power factor is low and medium frequency furnace must be reasonable to control the power factor, otherwise, the lower but electricity power consumption while will be fine, it's not like that.
Three tons of intermediate frequency furnace circulating water temperature high how to solve the medium frequency furnace circulating water charged a: intermediate frequency furnace cooling water overheat reasons, mainly because of induction coil is cooled in high temperature melting pot around for a long time, when the temperature in the furnace, the temperature of the circulating water gradually increasing, pool cubage small quantity of heat to send out, the higher the water temperature.
Solution: the pool of water return pipe, appropriate nozzle below to add a piece of drill hole full of large steel plate, to come back.
Intermediate frequency furnace in use process requirements for cooling water what answer: conditions of use: (
1, environment condition and building facilities, the device should be installed to no violent vibration, no conductive dust, no corrosive gas, the temperature is not higher than 40 ℃, relative humidity is not more than 85%, of the interior.
Room 2, the power supply should be insects, rodents, snakes measures, should have the exhaust ventilation equipment, fire equipment.
3, waste water should be waterproof.
Intermediate frequency furnace electrical schematic diagram?
Intermediate frequency furnace circulating water charged a: manufacturers generally will provide, and also may not too detailed, ask someone won't give.
What do you mean with potential connection principle?
In medium frequency furnace cooling water pipe connection answer: not electricity all the way, as far as possible not series up.
Intermediate frequency electric cabinet circulating water why not short circuit.
Answer: the moisture of intermediate frequency furnace two parts, the first part: the electrical cabinet circulating water, this part of the circulating water main in capacitor, SCR jacketed circulation, water cycle of the environment itself is ark and electrical insulation,
Look carefully the insulation mechanism on both sides of the silicon controlled rectifier)
, this is the first circuit and cabinet put oneself in another's position, the insulation between the why and the circuit part is not short circuit, it said.
Intermediate frequency furnace cooling water hydraulic circulating water charged a: how many intermediate frequency furnace kw - 500
1000 kw intermediate frequency furnace cooling water requirements: first, a total hardness 225 - water quality requirements
35 degrees (
CaO content is 225 -
35 mg equivalent)
B soluble solids.
Intermediate frequency furnace distribution flow about a: intermediate frequency devices harmonic component is very big, is likely to be caused by harmonic.
Intermediate frequency furnace circulating water charged how intermediate frequency furnace and cooling tower, technical data according to what to go with the intermediate frequency furnace circulating water charged a: cooling tower also known as the cooling tower and cooling towers.
Shandong fengyuan glass steel mills all cooling tower is energy-saving, develop because of lower motor installed capacity in the cooling tower at home and abroad.
Low noise and low noise type cooling tower water temperature drop is 5 - commonly
General 8 °, suitable for air conditioning and refrigeration, etc to cool the temperature drop.
Ultra low noise cooling tower (
On the basis of the low noise again.
How to do the safety protection of intermediate frequency electric furnace
medium frequency furnace circulating water charged a: do the safety protection of intermediate frequency electric furnace method: 1, the right configuration cooling water system, water medium frequency power supply, induction coil, cable and so on all need to use water for cooling, so water is very important to intermediate frequency electric.
Foshan Hengyang Furnace Manufacturing Co.,Ltd., as well, confirms that consumers who want ethically produced goods do the work of looking for them.
Foshan Hengyang Furnace Manufacturing Co.,Ltd. will be known for our leadership edge, through our passion for high standards, our respect for diversity and our commitment to create exceptional opportunities for professional growth so that associates can fulfill their highest potential.
Foshan Hengyang Furnace Manufacturing Co.,Ltd. also has an extensive line of products as induction heating furnace.
Foshan Hengyang Furnace Manufacturing Co.,Ltd. manufactures aluminum smelting furnace with innovative facilities and professional operation.
Foshan Hengyang Furnace Manufacturing Co.,Ltd.'s scrap melting furnace are sturdy, easy to operate, friendly work machines that deliver high-quality aluminium shell furnace for cast iron melting furnace purposes.